Sebaik apapun suatu printer pasti akan mengalami error, apalagi jika printer sering digunakan. Nah, pada postingan kali ini admin akan membahas tentang cara reset printer Canon IP2770/IP2700 yang biasanya bermasalah atau error dengan muncul kode E rror 5200 Waste ink Tank Absorber Full. Sobat jangan kuatir, error 5200 biasa terjadi pada canon ip2770 / ip2700. Printer Canon IP 2770 adalah printer ekonomis yang kinerjanya tak kalah bagus dengan printer merEk lain. Tak sedikit yang menggunakan printer ini untuk keperluan pribadi hingga perkantoran yang hanya cetak dokumen biasa seperti surat dinas, surat lamaran, laporan keuangan, dan lain sebagainya. Cara Reset Printer Canon ip2770/2700 + Download Softwarenya By dosen Posted on Cara reset printer canon ip 2770 – Dosentekno.com| Siapa yang tidak kesal saat buru-buru nge-print, tiba-tiba printer anda rusak, []. Reset Printer Canon Ip2770 Terbaru IndianaCARA RESET PRINTER CANON iP 2770 Cara Reset Canon iP2770 Eror 5B00: 1. Printer dalam keadaan hidup 2. Tekan tahan tombol RESUME kemudian tekan tahan tombol POWER masing-masing 5 kali lalu lepas kedua tombol tersebut bersamaan (Led akan blink sebentar kemudian akan nyala HIJAU) 3. Komputer akan mendeteksi device baru, cancel saja. Hal ini menunjukkan printer iP2770 dalam keadaan SERVICE MODE dan siap direset. Jalankan Resetter iP2770 v1074-nya: 1. Siapkan beberapa kertas di printer (ini untuk print pada waktu proses reset). Jalankan program Resetter iP2770 4. Klik 'MAIN', maka printer akan berproses, kemudian iP2770 akan print satu halaman dengan tulisan ' D=000.0 ' 5. Klik ' EEPROM Clear '. Kemudian klik ' EEPROM ', dan printer akan print hasil Resetter iP2770 7. Matikan Printer dengan menekan tombol POWER dan hidupkan kembali CONTOH. ERROR DISPLAY Errors are displayed by the LEDs, and ink low warnings are displayed by the Status Monitor. Operator Call Error (Alarm LED Blinking in Orange) Alarm LED blinking Error Corrective action 2 times No paper Set paper, and press the Resume/Cancel button to feed the paper. 3 times Paper jam Remove the jammed paper, and press the Resume/Cancel button. 4 times No ink Replace the ink cartridge(s), or press the Resume/Cancel button to continue printing without replacing the ink cartridge(s). Install mac os x on hp probook 4540s. • AMD USERS READ THIS: Though technically permitted, the general consensus on Hackintoshes with AMD CPUs is that they're more trouble than they're worth. A Hackintosh is a non-Apple computer that runs Mac OS X. 5 times The ink cartridges are not properly installed, or a non-supported ink cartridge is installed (the ink cartridge EEPROM data is abnormal). Install the ink cartridges properly. Or, confirm that the supported ink cartridges are installed. 7 times Ink cartridge not installed Install the ink cartridge(s), and close the access cover. 8 times Waste ink absorber full or platen waste ink absorber full warning (approx. 95% of the maximum capacity) Pressing the Resume/Cancel button will exit the error, and enable printing. 14 times Non-supported ink cartridge installed Replace the non-supported ink cartridge with the supported one. ![]() 16 times Used ink cartridge installed, or no ink Pressing the Resume/Cancel button will exit the error, and enable printing. Carriage error or Error Code 5100 Condition: An error occurred in the carriage encoder signal. Problems and Solutions: • Smearing or scratches on the carriage slit film - clean the timing slit film. • Foreign material or paper debris that obstructs the carriage movement; - remove foreign material. • Ink tank conditions; - re-seat the ink tanks. • If other solution fail, replace one off the following - Timing slit disk film - Carriage unit - Logic board - Carriage motor Line Feed error or Error Code 6000 Condition: An error occurred in the LF encoder signal. Problems and Solutions: • Smearing or scratches on the LF / EJ slit film - clean the LF / EJ slit film. Download Master Printer Canon Ip2770• Foreign material or paper debris in the LF drive; - remove foreign material. • If other solution fail, replace one off the following - LF / EJ slit film - LF / EJ timing sensor unit - Paper feed roller unit - Logic board - Paper feed motor Purge cam sensor error or Error Code 5C00 Condition: An error occurred in the purge unit. Problems and Solutions: • Foreign material or paper debris around the purge drive system unit; - remove foreign material. • If other solution fail, replace one off the following - Purge drive system unit - Logic board ASF sensor error or Error Code 5700 Condition: An error occurred in the ASF cam sensor. Problems and Solutions: • Replace one of the following: - ASF unit - PE sensor board unit - Logic board Internal temperature error or Error Code 5400 Condition: The internal temperature is not normal.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2019
Categories |